Shure MX415DUAL/C
Are you interested in purchasing this product?
Dual Capsule Gooseneck Microphone
When important matters are on the line, the MX415DUAL/C captures it all - twice. The microphone features two electret condenser heads, mounted in one unobtrusive housing, and two preamped outputs that deliver redundant audio for critical live multi-channel sound and professional broadcast applications. The MXA415D has an overall length of 34 cm and features gooseneck with flexible top section for optimal placement.
HOW IT WORKS
The MX415DUAL/C delivers redundant audio recording for applications that require premium results when failure is not an option. With a unique dual capsule design, every word is captured simultaneously by two cardioid cartridges, each to a separate output preamp - providing reliable multi-feed audio for a variety of applications.
WHY IT'S BETTER
All the details are captured
Design with unobtrusive dual microphone head and two channels ensures signal gets through.
Everything is covered
A complete set of accessories is included to meet a variety of placement needs, from lectern to desk to stage.
Clear signal
Microflex features Shure Commshield® technology to block RF interference from mobile devices, keeping the focus on the speech.
QUALITY IS IN THE DETAILS
15-inch gooseneck
Low-profile dual cardioid capsule design
Single flexible gooseneck for optimal microphone fitting
Mounts on table, lectern, stage or similar surface
General Description
The Shure Microflex® MX415DUAL dual-capsule gooseneck microphone features two electret condenser cartridges mounted in a single low-profile housing and two preamp-equipped outputs providing redundant audio for critical, multi-feed live sound and professional broadcast applications. With a 15” overall length, the MX415DUAL includes a flexible top gooseneck section for optimal placement, and includes all the mounting accessories required for installation into a lectern or tabletop configuration.
Features
- Wide dynamic range and frequency response for accurate sound reproduction
- Dual 1 cm cardioid Microflex® interchangeable cartridges
- Dual 5-foot cables exiting out bottom of mic, terminating in two TQG Connectors
- Two external in-line preamps
- Shock mount provides over 20 dB of isolation from surface vibration noise
- RF filtering with CommShield® technology
Interchangeable Cartridges
Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.
Windscreen
- Snap into place when fully seated.
- To remove, grip under the wider sides of the foam and gently pull.
- Provides "pop" protection of 30 dB for mesh and 40 dB for foam windscreens.
Installation
Mount the microphone using a flange or shock mount.
Important: The dot on the microphone and TQG connector indicates which cartridge is connected to which connector. The included RK100PK phantom-powered preamps converts the TQG connector to an XLR output.
A13HDB Flange:
- Mark and drill 3 starter holes for the screws using the flange as a template.
- Secure the flange to the mounting surface with screws.
- Thread the microphone clip to the flange, then mount the microphone to the clip.
Note: Use the extension tube with the microphone clip and flange if desired.
RPM640 Flange:
- Drill a 22 mm (7/8 in.) diameter hole in the mounting surface.
- Mark and drill 3 starter holes for the screws using the flange as a template.
- Insert the TQG connectors through the mounting flange.
- Slide the retaining ring over the bottom of the gooseneck base until is flush to the bottom of the flange, then press the ring firmly into place.
- Secure the flange to the mounting surface with screws.
A400SM Shock Mount:
- Drill a 44 mm (1-3/4 in.) diameter hole in the mounting surface.
- Mark and drill 3 starter holes for the screws using the shock mount as a template.
- Secure the shock mount to the mounting surface with screws.
- Insert the TQG connectors through the hole, then insert the microphone base.
Dimensions